Filter

Showing all 10 results

DT1 & DT2

DT1 General Purpose Digital Thermometers

The Rototherm DT1 is a micro processor based, battery operated, continuous reading, type K thermocouple input digital thermometer.

Two basic versions are available, both have clear four digit LCD displays with 12.7mm high characters and 1ºC/ºF resolution. 4/20mA signal re-transmission and MAX / MIN temperature logging can also be incorporated.

The DT1-1 is a 316 stainless steel rigid stem temperature indicator. The stem can be either 12.7mm or 6.35mm diameter with a reduced tip for fast response. The stem length and fitting, if required, can be user specified. The DT1-1 can be mounted directly on to a pipe line or vessel where direct, local temperature indication is required.

The DT1-2 is a remote reading instrument, designed for mounting on a panel, either with a three hole front flange or a back flange for surface mounting. The indicator is connected to the sensor by a 3mm diameter stainless steel mineral insulated cable which can be fitted with a compression fitting if required.

DT2 Digital Thermometers

Using common construction to the DT1, the DT2 is a high accuracy, high resolution digital temperature indicator. The DT2 uses a precision three wire thin film PT1000 resistance element as a sensor and can be supplied in both rigid stem and remote reading variants. In common with the DT1 series the DT2 can be supplied with 4/20mA signal re-transmission and MAX / MIN temperature logging.

The DT2 -1 is a rigid stem, direct mounted instrument for local indication, stem configurations are common with the DT1-1. A special derivative of this product is the DT2-3, this is fitted with a 12.7mm stem with a reduced tip and a captive 3/4” or 1” BSP hygienic fitting – primary application are Dairy, Brewing and Food Industries.

The DT2-2 enables the measuring instrument to be mounted remotely from the sensor and is available in two variants with differing cable protection systems and sensor housings.

The standard instrument has a PTFE protected cable and a 6mm diameter, 50mm long stainless steel sensor housing. A cable gland can be supplied loose on the cable to enable a sealed connection to be made to tanks, pipes etc. Where cable protection is required 6mm diameter stainless steel armoured cable is available, the stainless steel sensor housing is 12.7mm diameter with a reduced tip, a standard compression fitting can be supplied either loose or captive

on the housing.

ATEX Approved Intrinsically Safe Versions

The addition to the range of an intrinsically safe version allows this product to be standardised in all Pharmaceutical and Petro Chemical industries.

Both Thermocouple (DT1X) and RTD (DT2X) sensor instruments are offered.

ATEX Category

II 1G EEx ia IIC T4 (-20°C < Ta < +60°C)

DigiTemp Tx Transmitter

Any non intrinsically safe DigiTemp variant can be supplied as a two wire 4/20mA indicating temperature transmitter. Operating from a two wire DC power supply, the DigiTemp Tx can be configured during set up to re-transmit a 4/20mA signal across either the full, or part of the instruments measurement range. DigiTemp Tx is supplied with a 2 metre long connecting cable. Retransmission range must be advised at the time of ordering.

DT1 & DT2

DT1 General Purpose Digital Thermometers

The Rototherm DT1 is a micro processor based, battery operated, continuous reading, type K thermocouple input digital thermometer.

Two basic versions are available, both have clear four digit LCD displays with 12.7mm high characters and 1ºC/ºF resolution. 4/20mA signal re-transmission and MAX / MIN temperature logging can also be incorporated.

The DT1-1 is a 316 stainless steel rigid stem temperature indicator. The stem can be either 12.7mm or 6.35mm diameter with a reduced tip for fast response. The stem length and fitting, if required, can be user specified. The DT1-1 can be mounted directly on to a pipe line or vessel where direct, local temperature indication is required.

The DT1-2 is a remote reading instrument, designed for mounting on a panel, either with a three hole front flange or a back flange for surface mounting. The indicator is connected to the sensor by a 3mm diameter stainless steel mineral insulated cable which can be fitted with a compression fitting if required.

DT2 Digital Thermometers

Using common construction to the DT1, the DT2 is a high accuracy, high resolution digital temperature indicator. The DT2 uses a precision three wire thin film PT1000 resistance element as a sensor and can be supplied in both rigid stem and remote reading variants. In common with the DT1 series the DT2 can be supplied with 4/20mA signal re-transmission and MAX / MIN temperature logging.

The DT2 -1 is a rigid stem, direct mounted instrument for local indication, stem configurations are common with the DT1-1. A special derivative of this product is the DT2-3, this is fitted with a 12.7mm stem with a reduced tip and a captive 3/4” or 1” BSP hygienic fitting – primary application are Dairy, Brewing and Food Industries.

The DT2-2 enables the measuring instrument to be mounted remotely from the sensor and is available in two variants with differing cable protection systems and sensor housings.

The standard instrument has a PTFE protected cable and a 6mm diameter, 50mm long stainless steel sensor housing. A cable gland can be supplied loose on the cable to enable a sealed connection to be made to tanks, pipes etc. Where cable protection is required 6mm diameter stainless steel armoured cable is available, the stainless steel sensor housing is 12.7mm diameter with a reduced tip, a standard compression fitting can be supplied either loose or captive

on the housing.

ATEX Approved Intrinsically Safe Versions

The addition to the range of an intrinsically safe version allows this product to be standardised in all Pharmaceutical and Petro Chemical industries.

Both Thermocouple (DT1X) and RTD (DT2X) sensor instruments are offered.

ATEX Category

II 1G EEx ia IIC T4 (-20°C < Ta < +60°C)

DigiTemp Tx Transmitter

Any non intrinsically safe DigiTemp variant can be supplied as a two wire 4/20mA indicating temperature transmitter. Operating from a two wire DC power supply, the DigiTemp Tx can be configured during set up to re-transmit a 4/20mA signal across either the full, or part of the instruments measurement range. DigiTemp Tx is supplied with a 2 metre long connecting cable. Retransmission range must be advised at the time of ordering.

NC3 & NR3

100mm & 160mm dial sizes

• Fitted with unique anti-resonant section to dampen the effects of vibration

• Back or bottom entry versions

The Rototherm range of diesel exhaust thermometers provide an accurate and reliable indication of the exhaust gas temperature of diesel engines and generators.

The stem is fitted with a unique anti-resonant section which dampens out vibration of the instrument head, and eliminates the need for oil filling.

The use of the capillary type enables all the dials to be located on a single panel to provide immediate visual comparison of the performance of each cylinder.

NC3 & NR3

100mm & 160mm dial sizes

• Fitted with unique anti-resonant section to dampen the effects of vibration

• Back or bottom entry versions

The Rototherm range of diesel exhaust thermometers provide an accurate and reliable indication of the exhaust gas temperature of diesel engines and generators.

The stem is fitted with a unique anti-resonant section which dampens out vibration of the instrument head, and eliminates the need for oil filling.

The use of the capillary type enables all the dials to be located on a single panel to provide immediate visual comparison of the performance of each cylinder.

NC1 & NC2

100mm & 160mm dial sizes

• Stainless steel case (316 option)

• All stainless steel construction

• Back or bottom entry versions

• Available with a wide range of thermowells

• Can be fitted with electrical contacts

Where a display is required some distance from the sensing point, for example on an instrument panel, capillary thermometers should be used. The dial can be located up to 30 metres from the sensing point and isolated from dirt and vibration. The sensing bulb is connected by stainless steel microbore capillary, protected by stainless

steel tubing. For severe conditions, flexible armour can extend the entire length of the capillary. Alternative protections can be specified if required.

Models

NC1 General Purpose capillary Thermometers

Tough accurate thermometers housed in a gasket sealed diecast aluminium case with adjustable zero.

NC2 Stainless Steel Cased Thermometers

Reliable, accurate industrial thermometers housed in a stainless steel case with the option of 100mm or 160mm diameter dial.

NC1 & NC2

100mm & 160mm dial sizes

• Stainless steel case (316 option)

• All stainless steel construction

• Back or bottom entry versions

• Available with a wide range of thermowells

• Can be fitted with electrical contacts

Where a display is required some distance from the sensing point, for example on an instrument panel, capillary thermometers should be used. The dial can be located up to 30 metres from the sensing point and isolated from dirt and vibration. The sensing bulb is connected by stainless steel microbore capillary, protected by stainless

steel tubing. For severe conditions, flexible armour can extend the entire length of the capillary. Alternative protections can be specified if required.

Models

NC1 General Purpose capillary Thermometers

Tough accurate thermometers housed in a gasket sealed diecast aluminium case with adjustable zero.

NC2 Stainless Steel Cased Thermometers

Reliable, accurate industrial thermometers housed in a stainless steel case with the option of 100mm or 160mm diameter dial.

BL3

A range of surface mounting bimetallic thermometers suitable for testing, balancing and fault-finding on heating systems. They can be attached to a surface by an adjustable spring or magnet to give an immediate indication of temperature without drilling or cutting.

This range of bimetallic thermometers is equally suitable for use on pipelines or flat surfaces such as radiators, platens or hot plates.

Excellent thermal conductivity is provided by the aluminium housing to the bimetallic element, while the stainless steel case and bezel minimises dissipation of heat to the atmosphere.

BL3-01 Surface Temperature Thermometer attaches to pipes by means of a spring and rotating hook.Without the spring, the instrument can be used on horizontal surfaces.

A strong permanent magnet enables the BL3-02 thermometer to be easily attached to horizontal or vertical surfaces. It is ideal for checking surface temperatures prior to the application of special finishes.

BL3

A range of surface mounting bimetallic thermometers suitable for testing, balancing and fault-finding on heating systems. They can be attached to a surface by an adjustable spring or magnet to give an immediate indication of temperature without drilling or cutting.

This range of bimetallic thermometers is equally suitable for use on pipelines or flat surfaces such as radiators, platens or hot plates.

Excellent thermal conductivity is provided by the aluminium housing to the bimetallic element, while the stainless steel case and bezel minimises dissipation of heat to the atmosphere.

BL3-01 Surface Temperature Thermometer attaches to pipes by means of a spring and rotating hook.Without the spring, the instrument can be used on horizontal surfaces.

A strong permanent magnet enables the BL3-02 thermometer to be easily attached to horizontal or vertical surfaces. It is ideal for checking surface temperatures prior to the application of special finishes.

BL1 & 2

Suitable for use on food processing equipment, the completely sealed stainless steel stem makes Rototherm Light Bimetallic Thermometers the ideal choice.

Perspex windows can be supplied in place of glass if required

BL1 & 2

Suitable for use on food processing equipment, the completely sealed stainless steel stem makes Rototherm Light Bimetallic Thermometers the ideal choice.

Perspex windows can be supplied in place of glass if required

BH2

• 63mm, 100mm & 160mm dial sizes

• Stainless steel case (316 option)

• All stainless steel construction

• Back or bottom entry versions

• Available with a wide range of thermowells

• Can be fitted with electrical contacts

The Rototherm range of Heavy Duty Bimetallic Thermometers combines robust construction, making these instruments suitable for the most stringent environmental conditions, together with an accurately manufactured bimetallic coil, which ensures a long dependable life.

Rototherm bimetallic thermometers do not contain harmful fill fluids eliminating any possibility of process contamination.

Applications

Ovens, Dryers, Storage Tanks, Food Processing, Dairies, Breweries, Pharmaceuticals and Petro chemical Industries, Refining.

BH2

• 63mm, 100mm & 160mm dial sizes

• Stainless steel case (316 option)

• All stainless steel construction

• Back or bottom entry versions

• Available with a wide range of thermowells

• Can be fitted with electrical contacts

The Rototherm range of Heavy Duty Bimetallic Thermometers combines robust construction, making these instruments suitable for the most stringent environmental conditions, together with an accurately manufactured bimetallic coil, which ensures a long dependable life.

Rototherm bimetallic thermometers do not contain harmful fill fluids eliminating any possibility of process contamination.

Applications

Ovens, Dryers, Storage Tanks, Food Processing, Dairies, Breweries, Pharmaceuticals and Petro chemical Industries, Refining.

Field Mounted Temperature Transmitters

The field housings of the transmitter are either made of aluminum die cast or of stainless steel. The rating plates are made of stainless steel. The devices are available with a tube mounting kit or a wall mounting kit.

Field Mounted Temperature Transmitters

The field housings of the transmitter are either made of aluminum die cast or of stainless steel. The rating plates are made of stainless steel. The devices are available with a tube mounting kit or a wall mounting kit.

High Temperature Thermometers

High-temperature combustion, annealing and melting processes are usually executed without pressure at temperature up to 1800 °C (3272 °F). As a result, the selection of the appropriate thermowell is the greatest challenge for temperature measurement. Both the thermowell materials’ temperature resistance and their resistance to aggressive media are decisive. In conjunction with the appropriate thermocouple, the thermowell has a considerable effect on the temperature sensor’s measuring accuracy and service life.

You can benefit from optimal plant productivity and efficiency by selecting the appropriate and correctly dimensioned temperature sensor.

High Temperature Thermometers

High-temperature combustion, annealing and melting processes are usually executed without pressure at temperature up to 1800 °C (3272 °F). As a result, the selection of the appropriate thermowell is the greatest challenge for temperature measurement. Both the thermowell materials’ temperature resistance and their resistance to aggressive media are decisive. In conjunction with the appropriate thermocouple, the thermowell has a considerable effect on the temperature sensor’s measuring accuracy and service life.

You can benefit from optimal plant productivity and efficiency by selecting the appropriate and correctly dimensioned temperature sensor.

Process Industry Head Thermometers

Rough environmental conditions, hazardous areas, space-saving installation and flexible assembly are only some examples of the skills of our daily approved reliable temperature sensors.

Process Industry Head Thermometers

Rough environmental conditions, hazardous areas, space-saving installation and flexible assembly are only some examples of the skills of our daily approved reliable temperature sensors.

BH3

100mm, 130mm and 160mm case options

•  Silicone filling available

•  No contaminents – safe for food and chemical applications

• Available with a wide range of thermowells

The Rototherm range of Any Angle Bimetallic Thermometers allows movement of the adjustable head through 180º, through a full 360º rotation, thus allowing its position to be set for maximum readability after installation.

All welded stainless steel construction of the system/bellows assembly allows full angular adjustment of the case through 360º without the need for pointer adjustment.

The Any Angle Bimetallic Thermometer is available in either 100mm, 130mm or 160mm dial sizes with temperature ranges and stem lengths to suit most industrial applications.

BH3

100mm, 130mm and 160mm case options

•  Silicone filling available

•  No contaminents – safe for food and chemical applications

• Available with a wide range of thermowells

The Rototherm range of Any Angle Bimetallic Thermometers allows movement of the adjustable head through 180º, through a full 360º rotation, thus allowing its position to be set for maximum readability after installation.

All welded stainless steel construction of the system/bellows assembly allows full angular adjustment of the case through 360º without the need for pointer adjustment.

The Any Angle Bimetallic Thermometer is available in either 100mm, 130mm or 160mm dial sizes with temperature ranges and stem lengths to suit most industrial applications.